www.melanexjou.fora.pl

[loiwtjsf]

Buick CCD subframe welded leak detection system


Loss, punctuality transported to designated places. (2) system is composed of drum-type roller,[link widoczny dla zalogowanych], driven by a stepper motor. (3) When you need parts feeding, qualified transportation, rework product delivery, the control system will command all the logistics system in real time to run or stop the raceway. 5 Management System (1) coordinates detection, control, sorting, and material glistening operation between the various systems rhythm and beat. \(3) It is not only playing command and coordinate the operation of the system, start and stop. And, Liao to the size of the data for statistical testing, storage, development of statistical reports, and more than a hundred workers. 6. System performance is not f1) to determine whether the tainted 2l welds with welding or size not in place. 91,1 ~ 0 all scorpion better qualified. As long as there is not welded or not a standard to measure sub dismay. f2),[link widoczny dla zalogowanych], then sub-products for sound and light alarm, and shows off the seam position number. Amendments to facilitate the rapid return to achieve 1O0% of the qualified insanity. f3) of the system unit to provide daily report and monthly reports. Including the total number of detection,[link widoczny dla zalogowanych], the number of qualified products, the quantity of defective products. Also provide any welding and stitch a seam in the number of unqualified help, and the total percentage of the amount lost can be printed at any time Ⅲ. 7. Island of the shuttle system implementation unit site layout shown in Figure 4. E/41 Po roller 2 and then along the Gui Yuan TV station with 々, 3 cells of a dispute ye product roll four provinces, 5 out of a defensive unit, 6 a roll delivery rework, 7 points for a king ashamed f1) into Welding good bit subframe has been sent to the input roller was l. L will be the roll was sent to the testing station part 2,[link widoczny dla zalogowanych], place hair in place after the signal to the console 4. Then the computer field console control commands sent to the test station 2, the part positioning within the clamping fixture. Completed, the return signal to the computer. (2) data collection and transfer operations of the computer box 4 are part of the signal bar positioning holding that instruction fixture 2l open all ten secondary sources. Ten CCD 21 while the probe command to work, collecting data to 2l of welds. Then, the results obtained through the relevant interface, the data is transferred to the workstation 7. (3) determine compliance with the differential detection station 7 or the mode matching method to pull data from the information collected was the introduction of grid computing to determine whether or not the conclusion. Deposited in the database. Pick up test results and output. If you fail, make a sound and light alarm, and the display shows the weld failed to raise a few Hui. Foot-inch judgments as well. (4) points to determine whether or not wipe the table with the transfer is complete, the workstation immediately issued instructions detection system. Fluorescent secondary light source off, release the clamp. If the part is a qualified command control station 7 is sorting machine operator control box 4 part 5 will be eligible from the test station 2 3 roller to move on qualified products. Transmitted by the roller 3 to the next process. If Pakistan is the failure of parts measured, workstations light alarm Lo 7 that instructions on the screen showing in the first few welds; workstation operating box 4 through 7 at the same time sorting machine instructions part 5 will be disqualified from the test work bit 2 to move to rework on the roller 6. Pass by the roller 6 to rework the process again and again, according to rework displayed within the pit. (5) management station 7 on the one hand and the instruction of the function of the system between each beat. At the same time also record the date, time, size, determine the results of a series of data, a database of well kept. Also stands ready to provide a report output and printing. IV Conclusion weld through the four detection methods (hard rays, ultrasound, magnetic flux, CCD) the advantages and disadvantages, with Buick parts subframe comprehensive comparative analysis, the final choice CCD is the best option. It is a light, mechanical,[link widoczny dla zalogowanych], electrical Trinity secondary computer system control and management too. It contains f) automatic detection; (2) automated sorting (3) automatic pure logistics; (4) automation and control; (5) automated management functions constitute the five too. Hope that readers inspiration. * Welcome to subscribe to the 2002 \{large engineering technician gowns, economic managers, technical workers and related professional teachers and students. Journal friendship with the pregnancy four, quarter-end publication, subscription fee is 20 yuan / year. Remittance Address: Huai An Road 681, Shanghai (Shanghai Machine) Editorial Code: 200041 【Please indicate in the remittance \Bank: ICBC branch in Shanghai's Jingan Branch Account} 022 731 new gates for a l0O1273l090144075402l

相关的主题文章：


[link widoczny dla zalogowanych]

[link widoczny dla zalogowanych]

[link widoczny dla zalogowanych]